|Built-In:||Battery, GPS Location|
|Inputs:||Four dry contacts|
|Notifications:||Eight voice phone calls, plus six e-mail messages|
|Two status messages per day, 3+ year AA Lithium Batteries|
|Sensaphone SAT4D Remote Satellite Monitoring System|
|Sensaphone SAT4D One Year Communications Service|
|Sensaphone SAT4D Functional Diagram|
(click for larger image)
Remote Satellite Monitoring with 100% CoverageThe SAT4D System Allows you to Monitor Anything, Anywhere, and know where it is.
Pole Mount Kit for SAT4D
Product # FGD-SAT4D-PKIT
This kit provides all of the necessary parts to mount the SAT4D product onto a pole that is installed directly into the ground.
Product # FGD-0010
50ft. of 22-gauge shielded wire for connecting sensors to your sensaphone.
Sensaphone SAT4D One Year Communications Service
Product # FGD-SAT1Y
Sensaphone SAT4D One Year Communications Service
Magnetic Reed Door and Window Switch
Product # FGD-0006
The magnetic reed switch may be used with all Sensaphone models to detect any unauthorized entry or intrusion. They are usually installed on doors and windows to detect their opening and closing. Several magnetic reed switches may be wired in series.
Infrared Motion Detection Sensor
Product # FGD-0007
The passive infrared motion detection sensor can be used with all Sensaphone models to monitor the movement of warm bodies in a specific area. It will cause an alarm if motion is detected. Its range of detection covers approximately forty feet of area. Multiple sensors can be wired in series to a single output.
Spot Water Detection Sensor
Product # FGD-0013
The water detection sensor can be used with all Sensaphone models to detect the presence of water on a horizontal surface. Independently powered by internal lithium batteries. The batteries should last for approximately 3-5 years. When the batteries start to run down, the sensor will automatically cause an alarm dial out when no water is present. Multiple sensors can be wired in series to a single input.
Temp Alert Temperature Switch
Product # FGD-0022
The Temp Alert Temperature Switch can be used with all Sensaphone models to monitor air temperature from -30° to 130°F (-34° to 54°C). Simply determine the acceptable temperature limits for your application by adjusting the temperature limit arms. When the temperature exceeds the setting, the sensor triggers an alarm. The temp alert can be mounted to any wall or vertical surface. Multiple temp alerts may be wired in parallel to a single input. It requires no power for operation and mounts easily on any flat surface.
Humidistat Humidity Switch
Product # FGD-0027
The Humidistat Humidity Switch can be used with all Sensaphone models to detect a high or low humidity level. The device will cause your Sensaphone to activate an alarm when the humidity level reaches a set threshold. Made from high impact plastic with a brushed goldtone dial plate and a beige cover. A nylon sensing element provides long life and accurate humidity control. With a range of 10% to 60% RH level, the sensor causes an alarm when the humidity exceeds or falls below the set limit. Multiple sensors may be wired to a single input.
Smoke Detector for 110VAC
Product # FGD-0049
The Smoke Detector with built-in relay utilizes a photoelectric sensing method and is designed for use in commercial and residential applications. The device requires hard-wired 120VAC 60Hz power. The detector features two sets of dry alarm contacts: one form-A SPST and one form-C SPDT. The detector has tandem interconnect capability allowing up to 6 devices to be connected together. A 90dBA audible horn is included. The detector can be used with all Sensaphone models.
Smoke Detector for 110VAC w/ Battery Backup
Product # FGD-0049-B
The Smoke Detector with built-in relay utilizes a photoelectric sensing method and is designed for use in commercial and residential applications. The device requires hard-wired 120VAC 60Hz power, but also includes internal battery backup. The detector features two sets of dry alarm contacts: one form-A SPST and one form-C SPDT. The detector has tandem interconnect capability allowing up to 6 devices to be connected together. A 90dBA audible horn is included. The detector can be used with all Sensaphone models.
PowerOut Alert Power Failure Switch
Product # FGD-0054
A compact power outage monitoring device to detect power failures. Easily plugs into any 110 VAC receptacle outlet for operation. Comes with 15 feet of wire.
Zone Water Detection Sensor
Product # FGD-0056
The Sensaphone zone water detection sensor is for detecting the presence of water on a floor or in a FALSE ceiling. It comes with 10′ of WaterRope capable of covering a larger area than the FGD-0013 water sensor. Up to ten WaterRopes can be cascaded from a single sensor for even greater coverage. Works with all Sensaphone products and operates on two AA batteries (installed).
Water Rope Extension for Zone Water Detection Sensors
Product # FGD-0063
Extends the water detection rope on the FGD-0056 sensor by an additional 10 feet.
Float Level Switch
Product # FGD-0222
The Float Level Switch is a plastic side mounted float switch that is cost effective for level control applications in small tanks where it is more convenient to install a level switch through the sidewall of the tank. This style float switch can be rotated for Normally Open or Normally Closed operation. Combine two switches at different levels for high and low level or pump control or alarming.
|Name:||Sensaphone SAT4D Remote Satellite Monitoring System|
|Coverage:||The New Sensaphone SAT4D is designed to monitor a remote site no matter where it is located. Cellular coverage is getting better, but there are still many remote locations where cellular is not an option. The SAT4D uses direct satellite communications, which results in 100% coverage across the United States as well as many other countries.|
|Power:||Not only does the SAT4D make your communication easy, but it also takes away your power source worries, too. The new SAT4D remote monitoring system operates from 4 AA Lithium batteries (included). Mount it, connect your sensors, and walk away. The SAT4D will operate for at least 3 years on battery power. Place it anywhere, and only come back every three years to change the batteries.|
|Alarm Inputs:||The Sensaphone SAT4D can monitor up to 4 dry contact inputs for alarms. Each input can be either normally open or normally closed. User programmable recognitions times can be set individually for each input.|
|Alarm Notification:||When an alarm occurs on any of the input, the SAT4D sends a message via satellite that is delivered to the Sensaphone SAT4D website. From there, up to eight custom voice phone calls are made to notify the appropriate personnel of the alarm. Up to six e-mail messages can also be sent for alarms.|
|Web Interface:||All communications to and from the SAT4D product go through the Sensaphone SAT4D server. You can log in to your account on the SAT4D website at any time to check the latest status, to check previous alarm events, or to make programming changes.|
|Automatic Status Updates:||In addition to sending out alarm events, the SAT4D will automatically send two status reports per day to the website. The history of these 12 hour snapshots remain available on the SAT4D server for future reference.|
|GPS:||In addition to the remote monitoring and alarm notification features, the SAT4D also includes GPS location technology. This allows the option to monitor mobile assets, or just the convenience of seeing exactly where all of your remote sites are located.|
|Power Requirement:||Four AA Lithium batteries (included) provide 3+ years of service|
|Duplex Pump Control Logic:||No|
|Peer to Peer Control Logic:||No|
|Operating Conditions:||-30° to 60°C|
|-22°F to 140°F|
|Sensaphone SAT4D Brochure (pdf)|
|Sensaphone SAT4D Manual (pdf)|
|Wireless Solutions Brochure (pdf)|
|SAT4D Service Plan (pdf)|