Quick View		(larger image)
Built-In:	Power Failure, Sound Level, Temperature*
Inputs:	4 Wireless & 4 Hard Wired
Outputs:	1 Relay (manual or automatic control)
Notifications:	8 Custom Voice Phone Calls
Special  Features:	Wireless Sensors
Part  Numbers:	Sensaphone 2800 Wireless Monitoring System w/ Clear Door FGD-2800-CD
	Sensaphone 2800 Wireless Monitoring System w/ Solid Door FGD-2800-SD
Sensaphone 2800 Functional Diagram
(click for larger image)

Sensaphone 2800 Wireless Monitoring System

(Sensaphone Introduces Wireless Sensors)

Now you can monitor critical conditions at remote locations without running wires. Introducing the new Sensaphone 2800 with Wireless Sensor Technology.

Based on proven Sensaphone remote monitoring methods, the 2800 adds the ability to read sensor status from wireless sensors. And not just simple on/off status, or open/closed conditions. The Sensaphone Wireless Technology includes full analog capability so real world values can be monitored, like actual temperatures, real tank levels and flow rates.

You can use up to four of the Sensaphone wireless sensors with the 2800. A variety of wireless sensors types are available to choose from, including ...

• Temperature
• Humidity
• Power Failure
• Motion Detector
• Water on Floor

In addition to the wireless sensors, there are also two Wireless Interface modules. These allow you to connect to existing equipment or sensors and transmit their status back to the 2800 wirelessly. There is a Dry Contact wireless module, and even a 4-20mA wireless module. The 4-20mA wireless module even provides battery backed 24 VDC loop power for your transducer.

Stick It Anywhere!

Most of the Sensaphone Wireless Sensors run on batteries for up to 3 years. You can literally, just stick a sensor to the wall and start monitoring right away. The 2800 will scan, find the sensor, self configure and do most of the work for you. All you need to do is to record a custom voice message and fill in a few parameters.

Self Diagnostics

The Wireless Sensor Network is always being watched by the 2800. In addition to looking for alarms from the sensor values, it is also looking to make sure that each wireless sensor is fully functional and its batteries are full. If there are any problems with the wireless sensors, the 2800 will initiate a diagnostic alarm and notify the appropriate personnel immediately.

Sensaphone 2800 Wireless Monitoring System

Accessories

	Sensaphone 2800 Outdoor Weatherproof Antenna Kit Product # FGD-2810 The FGD-2810 Outdoor Weatherproof Antenna kit is designed to work with the Sensaphone 2800 Environmental Monitoring System. The weatherproof antenna allows you to place your Sensaphone 2800 in a location that would normally have reduced signal contact with the wireless sensors (such as in a metal cabinet or outside a building). It includes a mast mounting kit which includes a heavy duty steel bracket, and a pair of U'-bolts, this kit allows installation on masts up to 2.0" in diameter.
	Mini Surge Protector - Power and Phone Product # FGD-0067 The Traveler surge suppressor offers complete AC and phone line surge suppression for your Sensaphone and other electronic devices. The compact housing weighs less than 4 ounces. The retractable plug prevents scratching of expensive portable electronics. A set of RJ11 telephone line suppression jacks protect dialup and voice/modem lines. The suppressor offers 2 total outlets in a space saving direct plug-in format and diagnostic LEDs to warn of wiring problems and suppressor damage. $50,000 Ultimate Lifetime Insurance (USA & Canada Only).
	J Type Thermocouple/4-20mA Converter Product # FGD-0220 The thermocouple to 4-20mA converter is useful when monitoring very high or very low temperatures that can not be monitored with a standard Sensaphone temperature sensor. Thermocouples are available in a variety of packages that may be perfectly suited to your measuring application. Each thermocouple input module provides a single channel of thermocouple input which is filtered, isolated, amplified, linearized and converted to a 4-20mA output. Isolation is provided by transformer coupling, using a proprietary technique to suppress transmission of common mode spikes or surges. The modules have excellent stability over time and do not require recalibration.
	Bluetooth Cell Phone Interface Product # FGD-0230 The XLink allows your Sensaphone to dial and receive calls using any cell phone with Bluetooth technology. For example, suppose land-line telephone service was unavailable at the Sensaphone's location. By using the XLink you can provide telephone service to your Sensaphone by locating a cell phone next to the device. The XLink will send all incoming calls to the Sensaphone and when the Sensaphone needs to dial out the call will be seamlessly completed through the cell phone. The XLink is a wireless (Bluetooth) link between your Sensaphone and a cellular phone. This can be a cost-effective option considering that many cellular providers offer inexpensive options to add another phone. Perfect for access where a land line simply isn't available, the XLink is a must.
	AC Power Adaptor for 2800 Wireless Sensors Product # WSR-0190 Provides AC power for a Model 2800 wireless sensor so batteries are only used during a power failure.
	Wireless Repeater Product # WSR-0199 The WSR-0199 Wireless Repeater is designed to work with the Sensaphone 2800 Environmental Monitoring System. The wireless repeater allows you to have a greater distance between your wireless sensors and the Sensaphone 2800. It contains a more powerful radio transceiver which can transmit up to 300′ indoors and up to 4,000′ (line-of-sight). Only one repeater can be used per Sensaphone 2800. The sensor comes with a plug-in power supply and 3 AAA alkaline batteries for back-up in the event of an AC power failure.

Sensaphone 2800 Wireless Monitoring System

Sensors

	Wireless Temperature Sensor Product # WSR-0100 The WSR-0100 Wireless Indoor Temperature sensor is designed to work with the Sensaphone 2800 Environmental Monitoring System. This sensor includes a built-in radio transmitter and temperature element for monitoring temperature wherever the device is installed. You can also remove the internal temperature element and connect a remote temperature probe so that measurements can be made in a refrigerator, freezer or other harsh environment. The sensor comes with 3 AAA alkaline batteries which will power the sensor for up to 3 years. An optional plug-in power supply is also available in which case the batteries become a backup if main AC power fails.
	Wireless Dry Contact Sensor Product # WSR-0101 The WSR-0101 Wireless Indoor Dry Contact sensor is designed to work with the Sensaphone 2800 Environmental Monitoring System. This sensor includes a built-in radio transmitter and input terminals for connecting to any normally-open or normally closed output. (Use of this device with solid-state outputs is not recommended.) The sensor comes with 3 AAA alkaline batteries which will power the sensor for up to 3 years. An optional plug-in power supply is also available. The batteries then become a backup if main AC power fails.
	Wireless Power Failure Sensor Product # WSR-0102 The WSR-0102 Wireless Indoor Power Failure sensor is designed to work with the Sensaphone 2800 Environmental Monitoring System. This sensor includes a built-in radio transmitter, AAA alkaline batteries and a wall plug in power supply. The sensor will detect a loss of power at the outlet where the power supply is attached. The 3 AAA alkaline batteries will power the sensor and allow it to transmit alarm information in the event that AC power fails.
	Wireless Humidity Sensor Product # WSR-0103 The WSR-0103 Wireless Indoor Humidity sensor is designed to work with the Sensaphone 2800 Environmental Monitoring System. This sensor includes a built-in radio transmitter and humidity sensor element for monitoring humidity wherever the device is installed. The sensor comes with 3 AAA alkaline batteries which will power the sensor for up to 3 years. An optional plug-in power supply is also available. The batteries then become a backup if main AC power fails.
	Wireless 4-20mA Sensor Product # WSR-0104 The WSR-0104 Wireless Indoor 4-20mA sensor is designed to work with the Sensaphone 2800 Environmental Monitoring System. This sensor includes a built-in radio transmitter, 4-20mA input and a 24V loop power supply. The sensor can be used to monitor the output of any 4-20mA transducer. The sensor comes with a plug-in power supply and 3 AAA alkaline batteries which will power the sensor for several hours if main AC power fails.
	Wireless Motion Detector Product # WSR-0105 A waterproof device for measuring the temperature of fluids in a pipe. It features a 304 stainless steel probe and a brass WEL-B thermowell. Comes with 8 feet of wire.
	Wireless Spot Water Detection Sensor Product # WSR-0106 The WSR-0106 Wireless Spot Water Detection Sensor is designed to work with the Sensaphone 2800 Environmental Monitoring System. This sensor includes a built-in radio transmitter and water sensing probes for monitoring for the presence of water at a particular location. The sensor comes with 3 AA alkaline batteries which will power the sensor for up to 3 years.
	Wireless Zone Water Detection Sensor Product # WSR-0107 The WSR-0107 Wireless Zone Water Detection Sensor is designed to work with the Sensaphone 2800 Environmental Monitoring System. This sensor includes a built-in radio transmitter and ten feet of water sensing cable for monitoring for the presence of water in a particular area. The size of the monitored area can be extended by attaching additional lengths of WaterRope (FGD-0063) to the end of the included WaterRope. You can connect up to ten lengths of WaterRope (100′) to one Zone Water Detector. The sensor comes with 3 AA alkaline batteries which will power the sensor for up to 3 years.
	Extra 10′ Water Detection Rope Product # FGD-0063 Extends the water detection rope on the FGD-0056 sensor by an additional 10 feet.
	Magnetic Reed Switch Product # FGD-0006 The magnetic reed switch may be used with all Sensaphone models to detect any unauthorized entry or intrusion. They are usually installed on doors and windows to detect their opening and closing. Several magnetic reed switches may be wired in series.
	Infra-Red Motion Detector Product # FGD-0007 The passive infra-red motion detector can be used with all Sensaphone models to monitor the movement of warm bodies in a specific area. It will cause an alarm if motion is detected. Its range of detection covers approximately forty feet of area. Multiple sensors can be wired in series to a single output.
	Spot Water Detector Product # FGD-0013 The water detection sensor can be used with all Sensaphone models to detect the presence of water on a horizontal surface. Independently powered by internal lithium batteries. The batteries should last for approximately 3-5 years. When the batteries start to run down, the sensor will automatically cause an alarm dial out when no water is present. Multiple sensors can be wired in series to a single input.
	Temp Alert Product # FGD-0022 The Temp Alert can be used with all Sensaphone models to monitor air temperature from -30° to 130°F (-34° to 54°C). Simply determine the acceptable temperature limits for your application by adjusting the temperature limit arms. When the temperature exceeds the setting, the sensor triggers an alarm. The temp alert can be mounted to any wall or vertical surface. Multiple temp alerts may be wired in parallel to a single input. It requires no power for operation and mounts easily on any flat surface.
	Humidistat Product # FGD-0027 The Humidistat can be used with all Sensaphone models to detect a high or low humidity level. The device will cause your Sensaphone to activate an alarm when the humidity level reaches a set threshold. Made from high impact plastic with a brushed goldtone dial plate and a beige cover. A nylon sensing element provides long life and accurate humidity control. With a range of 10% to 60% RH level, the sensor causes an alarm when the humidity exceeds or falls below the set limit. Multiple sensors may be wired to a single input.
	Smoke Detector 110VAC Product # FGD-0049 The Smoke Detector with built-in relay utilizes a photoelectric sensing method and is designed for use in commercial and residential applications. The device requires hard-wired 120VAC 60Hz power. The detector features two sets of dry alarm contacts: one form-A SPST and one form-C SPDT. The detector has tandem interconnect capability allowing up to 6 devices to be connected together. A 90dBA audible horn is included. The detector can be used with all Sensaphone models.
	Smoke Detector 110VAC with Battery backup Product # FGD-0049-B The Smoke Detector with built-in relay utilizes a photoelectric sensing method and is designed for use in commercial and residential applications. The device requires hard-wired 120VAC 60Hz power, but also includes internal battery backup. The detector features two sets of dry alarm contacts: one form-A SPST and one form-C SPDT. The detector has tandem interconnect capability allowing up to 6 devices to be connected together. A 90dBA audible horn is included. The detector can be used with all Sensaphone models.
	Humidity Transmitter (4-20mA) Product # FGD-0052 A space mount, low profile humidity transducer. Transmits actually humidity levels to Sensaphone for programmable high and low alarm limits. Does not come with wire.
	PowerOut Alert Model PS-110 Product # FGD-0054 A compact power outage monitoring device to detect power failures. Easily plugs into any 110 VAC receptacle outlet for operation. Comes with 15 feet of wire.
	Zone Water Detector Product # FGD-0056 The Sensaphone zone water detector is for detecting the presence of water on a floor or in a FALSE ceiling. It comes with 10′ of WaterRope capable of covering a larger area than the FGD-0013 water sensor. Up to ten WaterRopes can be cascaded from a single sensor for even greater coverage. Works with all Sensaphone products and operates on two AA batteries (installed).
	Extra 10′ Water Detection Rope Product # FGD-0063 Extends the water detection rope on the FGD-0056 sensor by an additional 10 feet.
	External Microphone Attachment Product # FGD-0057 Provides listen-in and/or high sound alarm capability at a remote location away from your Sensaphone. Comes with 25 feet of wire.
	Carbon Monoxide (CO) Sensor Product # FGD-0065 Carbon Monoxide is a highly toxic gas that has no color or odor. The Sensaphone Carbon Monoxide sensor will allow you to monitor CO levels from 0-300 ppm with any Sensaphone that will accept a 4-20mA input signal. The 1″ x .5″ LCD displays the PPM and menu parameters. The sensor will require a 24VDC power supply to operate (Part # FGD-0053).
	Air Quality Sensor Product # FGD-0066 The Sensaphone Indoor Air Quality sensor will allow you to monitor levels of pollution from 0–100% with any Sensaphone that will accept a 4-20mA input signal. Popular applications include schoolrooms, office buildings, and parking garages. The Air Quality sensor uses a tin dioxide semiconductor sensor to detect oxidizable gases and is specially designed to have high sensitivity to gaseous organic materials which are components of indoor air pollutants. These air contaminants include cigarette smoke, cooking exhaust, automobile exhaust, solvents and many others. The sensor will require a 24VDC power supply to operate. (Part # FGD-0053)
	Carbon Dioxide (CO2) Sensor Product # FGD-0068 The Sensaphone Carbon Dioxide sensor will allow you to monitor levels of Carbon Dioxide from 0-2,000ppm with any Sensaphone that will accept a 4-20mA input signal. The sensor will need a 24VDC power supply to operate (Part # FGD-0053)
	Remote Temperature Sensor 2.8K Product # FGD-0100 The 2.8K Remote Temperature sensor enables monitoring temperatures at a location away from a Sensaphone unit. It will measure and report the exact temperature back to the Sensaphone unit to which it is attached. The Sensaphone can be programmed to trigger an alarm when conditions exceed the set high or low temperature limits. It may be mounted anywhere air temperatures need to be measured, however this model is recommended to be located in clean, dry environment. For outdoor use model FGD-0101 is recommended.
	2.8K Weatherproof Temperature Sensor Product # FGD-0101 The 2.8K Weatherproof Remote Temperature sensor enables monitoring temperatures at a location away from a Sensaphone unit. It will measure and report the exact temperature back to the Sensaphone unit to which it is attached. The Sensaphone can be programmed to trigger an alarm when conditions exceed the set high or low temperature limits. It may be mounted anywhere air temperatures need to be measured and is suitable for use in wet, dirty environments. This is a highly recommended sensor for every cold storage application above -20°F. For colder temperatures we recommend using sensor part number FGD-0101-TEF. NIST temperature certification is available.
	2.8K Ultra Low -85°C Temperature Sensor with Teflon Product # FGD-0101-TEF The 2.8K Ultra Low -85°C Temperature Sensor with Teflon enables monitoring temperatures at a location away from a Sensaphone unit. The Teflon coated wire will withstand temperatures down to -85°C. It will measure and report the exact temperature back to the Sensaphone unit to which it is attached. The Sensaphone can be programmed to trigger an alarm when conditions exceed the set high or low temperature limits. It may be mounted anywhere air temperatures need to be measured and is suitable for use in wet, dirty environments. NIST temperature certification is available.
	10K Remote Weatherproof Temperature Sensor Product # FGD-0102 The 10K Weatherproof Remote Temperature sensor enables monitoring temperatures at a location away from a Sensaphone unit. It will measure and report the exact temperature back to the Sensaphone unit to which it is attached. The Sensaphone can be programmed to trigger an alarm when conditions exceed the set high or low temperature limits. It may be mounted anywhere air temperatures need to be measured and is suitable for use in wet, dirty environments.
	10K Indoor Decorator Zone Temperature Sensor Product # FGD-0103 The 10K indoor decorator zone temperature sensor offers precision room temperature sensing in an attractive wall-mounted enclosure. Accurate to 0.36°F (0.2°C) with a sensing range of 35° to 140°F. The indoor decorator comes in a beige plastic enclosure, with a tan metal face plate. The sensor is designed to be wall-mounted indoors where appearance is important. The separate base plate may be mounted directly to the drywall or on a standard electrical outlet box without adapters. The cover is secured with tamper resistant hex screws.
	10K Outdoor Air Weatherproof Temperature Sensor Product # FGD-0104 The 10K Outdoor Air Weatherproof Temperature sensor is a sensitive temperature element with a stainless steel tube sheathe. It is mounted inside a ventilated, treated weather-resistant PVC shield to minimize radiant energy effects and mounted on a weatherproof outlet box for easy outdoor installation. Accurate to ±0.36°F (0.2°C) with a sensing range of -30° to 140°F. Eight feet of 24AWG wire is included.
	10K Immersion Temperature Sensor Product # FGD-0105 The 10K Immersion temperature sensor is a waterproof temperature sensor for measuring the temperature of fluids inside a pipe. It's constructed of brass WEL-B thermowell (which screws into a customer-supplied 0.5″ NPT saddle or Thredolet® fitting in a pipe). It fits into a thermowell via a brass 0.125″ NPT fitting. Accurate to ±0.36°F (0.2°C) and has a sensing range of 10° to 230°F. It also includes 8′ of 24AWG wire.
	2.8K Temperature Sensor with Glass Bead Vial Product # FGD-0107 The FGD-0107 is ideal for cold storage temperature monitoring. The glass bead filled vial will buffer any momentary fluctuations that may cause a preliminary alarm dial out, such as defrost cycles, opening of doors, and fans circulating air. The glass beads will slow the response time of the sensor allowing normal daily operations to occur without having an alarm initiated. This is a highly recommended sensor for every cold storage application above -20°F. For colder temperatures we recommended using sensor part number FGD-0107-TEF.
	2.8K Ultra Low -85°C Temperature Sensor with Glass Bead Vial and Teflon Cable Product # FGD-0107-TEF The FGD-0107-TEF is ideal for cold storage temperature monitoring. The glass bead filled vial will buffer any momentary fluctuations that may cause a preliminary alarm dial out, such as defrost cycles, opening of doors, and fans circulating air. The glass beads will slow the response time of the sensor allowing normal daily operations to occur without having an alarm initiated. The Teflon coated wire will withstand temperatures down to -85°C. This is a highly recommended sensor for every cold storage application below -20°F.
	Float Switch Product # FGD-0222 The FGD-0222 float switch is a plastic side mounted float switch that is cost effective for level control applications in small tanks where it is more convenient to install a level switch through the sidewall of the tank. This style float switch can be rotated for Normally Open or Normally Closed operation. Combine two switches at different levels for high and low level or pump control or alarming.

Sensaphone 2800 Wireless Monitoring System

Specifications

Sensaphone 2800 Wireless Monitoring System

Support Documents/Downloads

	Sensaphone 2800 Sales Literature (pdf)
	Sensaphone 2800 Owner's Manual (pdf)

Sensaphone 2800 Wireless Monitoring System

Video